Commercial
Epoxy floor systems for warehouses, aircraft hangars, auto shops, showrooms and plant floors. Safety striping, walkways and logos go right into the floor.
Learn More
A hangar floor coating has to carry aircraft tires and rolling equipment. It also has to stand up to jet fuel, oils and hydraulic fluid. We coat T-hangars, private and corporate hangars, maintenance and FBO hangars, and museum hangars across Greater Houston. This work is part of our commercial epoxy flooring, with the same prep and crews.
We coated the hangar floors at the Lone Star Flight Museum at Ellington Airport. The museum's two hangars total 60,000 air-conditioned square feet. A customer wrote that the museum moves 40 or more planes a month across them. We have installed floor coatings across Greater Houston since 2008, more than 3.5 million square feet in all.
Tell us about the job. We will get right back to you.
Prep comes first. We diamond grind the slab and repair cracks and joints. Then we test the concrete for moisture, and a vapor barrier primer goes down when the reading calls for one. A U.S. Navy hangar floor coating specification also calls for measuring the slab's moisture vapor emission before coating.
Hangar floor epoxy goes down next as the base coat, because epoxy bonds to concrete best. Over it goes a urethane, polyaspartic or polyurea topcoat that takes the wear. One hangar flooring guide calls epoxy under a urethane topcoat a seamless, chemical resistant surface. Commercial builds like this typically run 2 to 3 millimeters thick.
Light floors bounce the overhead light back up. Coating makers' hangar guides say a hangar floor should reflect overhead lighting so crews can see spills and dropped tools. We install high-gloss white or light gray as a solid color epoxy floor.
The same hangar flooring guide calls for a non-slip surface, even when the floor is wet or oily. It also notes that a smooth finish makes equipment easy to move. So walkways and wet areas can take texture from a quartz epoxy floor system or an aluminum oxide additive. Our page on anti-slip floor coatings covers how we pick the texture level.
Safety striping goes into the coating, too. That guide also lists clearly marked safety lines and designated walkways among the features to consider. We lay out walkways and work zones in the colors you choose, and logos can be set into the floor.
Conroe-North Houston Regional Airport hosts over 300 aircraft and 240 hangars. West Houston Airport has 60 T-hangar units, plus community and private hangars. Sugar Land's regional airport focuses on corporate aviation, and the city calls it the fourth largest in the Houston area. Our service area runs about 40 miles out from our Memorial office, north to Conroe and south to Alvin.
A hangar floor job starts with an empty hangar. The aircraft move out for the work, and the coating cures before they roll back in. We plan that schedule with you ahead of time. You can see more of our hangar and commercial work on our project page.
Free, no-obligation estimates across Greater Houston, from Conroe to Alvin.
(281) 831-5656From the first call or text to the walk-through on the finished floor, here is how it goes.
Reach us at (281) 831-5656 and tell us about the floor. We book estimates on weekdays.
We measure the slab, look at its condition and run a moisture test. Then you get a quote for the system we recommend.
Pick the color and finish from samples. Options include full flake, solid color, quartz and metallic.
We diamond grind the slab and repair cracks and joints. A vapor barrier primer goes down when the moisture test calls for it. Then comes the base coat, the flake or pigment broadcast, and the clear topcoat.
Most garages are a two-day job, and a metallic floor takes about three days. We do a final walk-through and tell you when to drive on the floor.
Common questions about hangar floors across Greater Houston, from Conroe to Alvin. If yours is not here, call or text and ask.
Epoxy floor systems for warehouses, aircraft hangars, auto shops, showrooms and plant floors. Safety striping, walkways and logos go right into the floor.
Learn More
A pigmented epoxy base under a clear topcoat, in one even color from bone and tan to gray, slate and safety red. The simplest finish we install, and the one that makes a garage or shop read as one clean surface.
Learn More
Slip-resistant coatings for floors that get wet or see heavy traffic. We build the grip into the floor with a quartz broadcast, an aluminum oxide additive or a textured topcoat.
Learn MoreMore than 3.5 million square feet of floor coatings are down across Greater Houston. Four crews keep the schedule moving.
Epoxy, polyaspartic and polyurea come from one company. We match the build to your slab, your use and your schedule.
We look at the slab, measure it and run a moisture test before we quote. Quotes often come back within a day.
The work is backed by a written warranty. Ask us for the terms, and we stand behind the work.
Real reviews from real floor coating jobs on Google, garages to hangars.
These guys did my garage floor back in November, Pablo really knows the technical knowledge and recommend a vapor barrier to be put down first. 3 months in and it still looks brand new. Went with Folsom color choice. Super easy to work with and plan around the drywall crew. Highly recommended!
I work for a custom home builder in the Houston area and we have been using Xpedite Coating for many years on our garage epoxy floors. They are very professional and timely and always leave the site clean after they are finished. I would highly recommend them for your next epoxy flooring need.
I used Xpedite Coatings twice to finish my epoxy flake garage floor at 2 properties. This guy is professional at what they do. The crew came and finished the job in a timely manner. The results look great and price is competitive. Highly recommended.
Tell us about your floor and we will come out, look at the slab and price it. Call or text (281) 831-5656, or send the form and we will follow up.
Tell us about the job. We will get right back to you.